Primary crusher accepts input sizes as large as 36″ (900 mm).
Available in three models.
Suitable for compressive strengths as high as 16,000 psi (110 Megapascals).
Adjustable to vary output size.
Typical output sizes are 4″ to 8″ (100 to 200 mm).
Adjustable to compensate for wear.
Spring loaded relief mechanism provides tramp iron protection.
Double Roll Crushers
Models for stone or coal.
Adjustable to vary output size.
Typical output sizes are 2″ (50 mm) or less.
Adjustable to compensate for wear.
Spring loaded relief mechanism provides tramp iron protection.
Segmented roll shells are standard on all models.
Clinker Grinders
A specialized single roll design.
Flange to flange size designed to replace other makes.
Suitable for water impounded hoppers when required.
Hinged maintenance door permits segment replacement without removing crusher from your system.
Frozen Coal Crackers
Chain driven single roll design.
Designed for under hopper or pile use.
Reduces frozen lumps to conveyable size.
Capable of starting under load.
One Way Models
Three models available for both primary and secondary applications.
Large reduction ratios are possible with most materials.
Tramp iron traps are provided on all sizes.
Special non-clog model available for sticky materials.
Reversible Models
Typical input sizes are 6″ (150 mm) or smaller.
Forged steel hammers are available on most models.
Adjustable to vary output size.
Typical output top sizes are 1-1/2″ (38 mm) to 1/8″ (3 mm).
Adjustable to compensate for wear.
Tramp iron protection on all models
jaw crusher
Our double toggle design minimizes wear.
Straight line crushing action.
Unique spring loaded flywheel eliminates the need to replace toggles for tramp iron protection.
Enclosed and lubricated drive extends component life.
Grinding Mills
End peripheral discharge style.
Produces minimum fines.
Robust roller and tire supported cylinder.
Integral drying is available if needed.
Roll crushers models
Roll crushers are used mainly for crushing easily fractured materials such as soft limestone , chalk, and clay to between 1/3 and 1/5 of its original size.
Roller Crusher Type E*
The Roller Crusher Type E* consists of two rollers with cast bosses. One of the roller shafts is adjustable while the other has a fixed position and is provided with a flywheel. The gap between the two rollers can be varied according to the degree of crushing required. The motor power is transmitted through a gear drive and two cardan shafts to permit the adjustment of the space between the rollers. Both rollers have scrapers to remove any material sticking to the surface.
Roller Crusher Type E
The Roller Crusher Type E machinery is overload-protected by a plate punching device connected to the bearing of the adjustable roller and a motor safety switch. If an extremely hard object is jammed between the rollers, the punching device is activated so that the crusher and feed stop. The frame structure consists of welded and cast steel parts which are bolted together. The rollers incorporate grease-lubricated roller bearings. The toothed wheels on the gear-drive are oil-immersed with grease lubricated shaft bearings. This attention to detail makes our roll crushers reliable to operate and low maintenance.
Roller Crusher Type TS**
The Roller Crusher Type TS**, designed for soft chalk and clay, is fitted with toothed roller sections for tearing large blocks of material before they are crushed in a subsequent process. Roll crusher performances vary according to the degree of crushing required and the consistency of the material.
**TS = roller crusher with toothed sections (120 cm roller diameter x 150 cm roller length)
Archives
Recent Posts
Categories
Calendar
Meta
Roll Crushers Models and roller crushers
Single Roll crushers
Double Roll Crushers
Clinker Grinders
Frozen Coal Crackers
One Way Models
Reversible Models
jaw crusher
Grinding Mills
Roll crushers models
Roll crushers are used mainly for crushing easily fractured materials such as soft limestone , chalk, and clay to between 1/3 and 1/5 of its original size.
Roller Crusher Type E*
The Roller Crusher Type E* consists of two rollers with cast bosses. One of the roller shafts is adjustable while the other has a fixed position and is provided with a flywheel. The gap between the two rollers can be varied according to the degree of crushing required. The motor power is transmitted through a gear drive and two cardan shafts to permit the adjustment of the space between the rollers. Both rollers have scrapers to remove any material sticking to the surface.
Roller Crusher Type E
The Roller Crusher Type E machinery is overload-protected by a plate punching device connected to the bearing of the adjustable roller and a motor safety switch. If an extremely hard object is jammed between the rollers, the punching device is activated so that the crusher and feed stop. The frame structure consists of welded and cast steel parts which are bolted together. The rollers incorporate grease-lubricated roller bearings. The toothed wheels on the gear-drive are oil-immersed with grease lubricated shaft bearings. This attention to detail makes our roll crushers reliable to operate and low maintenance.
Roller Crusher Type TS**
The Roller Crusher Type TS**, designed for soft chalk and clay, is fitted with toothed roller sections for tearing large blocks of material before they are crushed in a subsequent process. Roll crusher performances vary according to the degree of crushing required and the consistency of the material.
**TS = roller crusher with toothed sections (120 cm roller diameter x 150 cm roller length)